Caja para 4 cupcakes. Diy

Caja para 4 cupcakes. Diy


Today in the corner of Atir we will make a box four cupcakes let’s start at the base of the box We cut a piece of cardboard of 49 centimeters by 30.5 centimeters this piece we will measure and 10.5 cm from the edge inward and do it on both sides to know that we have done well the space we have left between brand and brand we have to measure 28 centimeters back to the brands that we had done and we will draw a line to below that will measure 10.5 cm centimeters and then we will close forming a rectangle I leave a schema is easier if you follow him here we have a rectangle and we will create another increasing each side 9.5 centimeters thus We form a third rectangle that will measure 10.5 cm high simply extend the line to the end Now let’s create some tabs on the sides of the rectangle that will measuring 4.5 by 10.5 centimeters we will also create a tab on the box is simply center extend the line to the far end thus and then we will also create some tabs in the third rectangle we simply reference the rectangle number 1 and this is the figure that has to be us in our piece of cardboard or cardboard I put all the little holes number to avoid getting lost in the Explanation If you notice, too many rectangles on the sides I’m marking in red and these gaps are going to cut the next step will bend the lines that have marked for this I’m going to help me a pair of scissors and a ruler start by vertical lines and simply pass the scissors pressing a little without breaking the paperboard and we repeat this operation for all lines then we will separate the lashes we cut this way to facilitate attachment of the flanges and do not rub when mounted let’s trim tabs slightly this way and we do this with all when you already have it we can mount the box to see how we have left I subject with tweezers because I will first decorate we need to cover a piece of 20 cm by 33. 5 centimeters the procedure is similar to the previous first let’s make 2.5 centimeters from the edge and then we will draw a line of 5 centimeters long and forming a closed rectangle or bar lengthen the rectangle drawing a line of 10 centimeters and so close We ended this bar extending the vertical line to the end the next step is to extend the horizontal lines leaving four and a half centimeters from the other bank explaining it another way, what we have to do is form the same bar we did at the beginning on the other side and in the middle we will form rectangles here I see that I have left those four and a half centimeters and I make a stripe verticale this way extension cable lines intersect and leave the same way that the other side now I measure three centimeters from the line of the rectangle that is above out to the edge of the part and I draw a line in this way and I do the same with box it in the bottom Note that I am measuring from the inside line out to the edge this is very important these gaps have been left out are going to cut and now let’s bend the same way we did with the base we will also separate the lashes be cut between lines 9 and 3, 6 and 9, 1 and 7, and 4 and 7 It is very important to do it this way also we will make a small cut so they do not rub together I’ll ride to check that it has been well optionally we can make a small window our box. We reference the inner rectangle. And we measured 1.5 cm from its lines inward In this way we will create a rectangle inside then cut it I’ll decorate with decorative paper The next step is to glue on the window, a piece of acetate and I’m going to do with hot glue I apply the glue and I’m putting in this way This we must do for the inside cap that is what will be inward we can mount the lid and let uniting all tabs with hot glue We do the same with the base of the box we can only make cupcakes support we need a rectangle 27 centimeters by eight centimeters and medium On this piece we will make some tabs 2 cm high in this way Then a small squares formed in the side right corners of the tabs you just have to extend the lines until they intersect and cut to make reference holes taking this capsule It is medium in size and this will determine the number of cupcakes that they will fit in your box I helped the capsule to mark the distribution of holes and then short to form the support I make small cuts between tabs Note that only I do it for the longest part of the support and now we will fold the other lines and we can already ride to give greater resistance we can glue the tabs but sooner if we want we can also decorate and you are ready to introduce it into our box only need to put the cupcakes but this time I have made cupcakes If you liked this video I would love you gave to me like and would share it Also you can subscribe to the channel to not miss anything and you can follow me on Facebook and in my blog

Only registered users can comment.

Leave a Reply

Your email address will not be published. Required fields are marked *